Grain-systems Tanks PNEG-4075G User Manual Page 106
- Page / 170
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 7: Roof Assembly
Installing the 6–Hole Intermediate Purlins
Intermediate purlins must be installed to connect each A-frame roof rafter assembly together. The inter-
mediate purlins connecting each A-frame roof rafter assembly have six holes on each side to secure them
with the purlin clips.
Before You Begin
All A-frame roof rafter assemblies must be installed and secured to both the center collar and the eave
brackets.
What You Should Know
IMPORTANT: The A-frames may have X-braces attached to the purlins. Before installing intermediate pur-
lins, make sure to loosen and remove the flange bolt and the flange nut securing the X-
braces with lower purlin clips and the rafters in the adjacent A-frames (if available).
1. Install the intermediate purlin (H) to the purlin clips (D and E) located outside of each A-frame roof
rafter assembly (A).
2. Attach a lower left purlin clip (J) and lower right purlin clip (K) to the purlin (H).
3. Install six flange bolts (B) and six flange nuts (G) to each end of the purlin (H) securing the intermedi-
ate purlin to the purlin clips.
4. Install three flange bolts (F) and three flange nuts (I) to the lower left purlin clip to secure the lower left
purlin clip with the A-frame rafter and the lower right purlin clip in the adjacent A-frame.
NOTE: If X-bracing is installed in the adjacent A-frames, ensure that it is also assembled together
with the purlin clips and rafter.
5. Install three flange bolts (F) and three flange nuts (I) to the lower right purlin clip to secure the purlin
clip with the A-frame rafter and the lower left purlin clip in the adjacent A-frame.
NOTE: If X-bracing is installed in the adjacent A-frames, ensure that it is also assembled together
with the purlin clips and rafter.
6. Tighten the hardware to the recommended torque specifications. See Bolt Torque Specifications,
page 24.
106 Pneg-4075G 75 Ft Diameter 40-Series Bin
- 75 Ft Diameter Bin — Gamma 1
- Contents 3
- Table of Contents 4
- 1 Safety Precautions 7
- Cautionary Symbols 9
- Safety Decals 10
- Chapter 1: Safety Precautions 11
- Safety Sign-off Sheet 13
- 2 General Overview 15
- Chapter 2: General Overview 16
- Construction 17
- Sample Gauge Sheet 20
- 3 Hardware Requirements 23
- Bolt Torque Specifications 24
- Identifying Bolt Grades 25
- Bolt Identification 27
- Bolt S-275 27
- Bolt S-10260 27
- Bolt S-277 27
- Bolt S-7485 28
- Bolt S-7487 28
- Bolt S-7486 28
- Bolt S-7488 29
- Bolt S-10252 29
- Bolt S-10261 30
- 4 Assembling Sidewall Sheets 31
- 5 Base Angle Installation 37
- example 38
- Anchor Bolt Detail 39
- 6 Stiffeners 43
- Chapter 6: Stiffeners 44
- Standard Stiffeners 45
- Top Stiffeners 46
- Stiffeners Splice 47
- Base Stiffeners 48
- Base Boots 49
- Two-Ring Stiffener (16 Ga) 50
- Connection 50
- Stiffener (16 Ga) 51
- Two-Ring Stiffener (0–14 Ga) 53
- (2–8 Ga) Connection 53
- Base Stiffener (2–8 Ga) 54
- Stiffener (10–16 Ga) 56
- Base Boot 60
- Stiffener with Insert 61
- 7 Roof Assembly 67
- Assembling a Laminated Rafter 74
- Assembling Purlin Number 6 80
- Assembling Purlin Number 5 81
- Assembling Purlin Number 4 84
- Assembling Purlin Number 3 86
- Assembling Purlin Number 2 88
- Assembling Purlin Number 1 90
- Assembling a Double A-Frame 92
- Assembling the Center Collar 94
- Center Collar Placement 97
- Chapter 7: Roof Assembly 100
- Attaching the Roof Panels 110
- Installing the Roof Flashing 115
- 8 Accessories 127
- Installing Roof Ladder Steps 128
- Chapter 8: Accessories 129
- Roof Ring Placement 130
- Installing a Roof Ring 131
- Assembling the Roof Exhauster 136
- Assembling the Auto Roof Vent 140
- Installing the Manway Cover 144
- Ladder Section Assembly 145
- Inside Ladder Placement 146
- Wind Ring Requirements 164
- Installing Wind Rings 165
- Warranty Extensions: 169
- Conditions and Limitations: 169
- Copyright © 2013 by GSI Group 170
- Printed in the USA 170
- CN #307887 170
Related products and manuals for Equipment Grain-systems Tanks PNEG-4075G
(50 pages)
(54 pages)© 2020, manymanuals.com. All rights reserved. | 5.022 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals